WIZ-105SR merupakan modul serial to ethernet gateway yang siap pakai. NM7010B Spesifikasi : - Berbasis GC89L591A0 dan W5100. - Kompatibel dengan modul EG-SR-7150MJ. - Antarmuka ethernet 10/100 Mbps (auto sensing). - Antarmuka UART TTL 3,3V (TXD, RXD, RTS, CTS). - Komunikasi serial maks. 230 Kbps. - Mendukung protokol TCP/UDP/IP/ARP/ICMP/MAC/Static/DHCP/PPPoE/DNS. - Mendukung perintah dari port UART. - Tersedia program konfigurasi yang mudah digunakan dan handal.

WIZ110SR merupakan modul serial RS232 to ethernet gateway yang siap pakai. Spesifikasi : - Berbasis GC89L591A0 dan W5100. - Antarmuka ethernet 10/100 Mbps (auto sensing). - Antarmuka UART RS232 (TXD, RXD, RTS, CTS). - Komunikasi serial maks. 230 Kbps. - Mendukung protokol TCP/UDP/IP/ARP/ICMP/MAC/Static/DHCP/PPPoE/DNS. - Mendukung perintah dari port UART. - Tegangan kerja +5V DC. - Tersedia program konfigurasi yang mudah digunakan dan handal. - Mendukung WIZ VSP (Virtual Serial Port).

Evaluation board untuk modul Webserver W220IO Spesifikasi : - Berbasis W220IO - Memiliki 2 input tegangan analog - Memiliki 2 output tengangan analog - 1 buah konektor RS-232 (DB9) - 1 buah konektor RJ-45 - 8 buah LED SMD sebagai output digital dari WIZ220IO - 8 buah switch sebagai input digital untuk WIZ220IO - Berfungsi sebagai Embeded Webserver - Include : WIZ220IO, WIZ220IO Baseboard, kabel serial, kabel LAN, adaptor

WIZ812MJ merupakan modul antarmuka jaringan yang berbasis W5100. Spesifikasi : - Berbasis W5100 hardwired TCP/IP stack. - Mendukung TCP, UDP, IP, ARP, ICMP, IGMP, PPPoE, MAC. - Antarmuka MCU bus dan SPI, dengan pitch header 2,54mm. - Mendukung auto MDI/MDIX. - Dilengkapi LED indikator network status (FDX, TX, RX, LINK, Collision). - Tegangan kerja +3,3V DC. - I/O dapat menoleransi level tegangan 5V. www.wiznet.co.kr

WIZ830MJ merupakan modul antarmuka jaringan yang berbasis W5300. Spesifikasi : - Berbasis W5300 hardwired TCP/IP stack. - Mendukung TCP, UDP, IP, ARP, ICMP, IGMP, PPPoE, MAC. - 8 SOCKET mandiri yang dapat bekerja secara simultan. - Antarmuka MCU BUS, dengan pitch header 2,54mm. - Mendukung lebar data 16 bit ataupun 8 bit. - Memiliki fitur DMA. - Tegangan kerja +3,3V DC. - I/O dapat menoleransi level tegangan 5V. cts] www.wiznet.co.kr

Products for the WTV020 chip plug-in SD card module, support 32M to 1GBit capacity card; Supports the FAT file system, SD card storage carrier; Support to play the WAV and 4Bit ADCPM format; Support for automatic identification folder and voice file playback; You can play background music and commercials language; Control mode key control, second-tier the control and UART232 serial control; WTV master chip WTV020-16SOP WTV020-20SOP two packages, both; Can any segment voice playback; Operating voltage: DC2.6-3.6V; Store content classified by folder, easy to operate. 2, Product Overview WTV020 plug-in SD card voice module, the master chip the optional WTV020-the 16S and WTV020-20S package chip. Voice updates directly through the SD card reader on a PC replacement. Control mode also change the SD card to store a TXT file. This module supports the FAT file system. Support WAV and ADPCM file playback. Support for two-wire serial control mode, the touch of a button and UART232 serial manner. Can automatically identify the voice sampling rate, and voice file format.

X-Band Motion Detector merupakan modul pendeteksi gerakan (motion detector) yang bekerja pada frekuensi X-Band 10,525 GHz. Modul ini bekerja berdasarkan efek Doppler dan mengindikasikan adanya gerakan melalui osilasi (high/low) pada pin output. Modul ini dirancang untuk mendeteksi adanya pergerakan bukan untuk mengukur kecepatan dari obyek yang bergerak. Dimensi X-Band Motion Detector : 1.83 x 1.87 x 0.69 in (46.5 x 47.5 x 17.6 mm) Spesifikasi X-Band Motion Detector: Bekerja berdasarkan efek Doppler pada frekuensi 10,525 GHz. Mampu mendeteksi gerakan dibalik dinding atau jendela (dinding/jendela non logam). Dirancang untuk mendeteksi gerakan bukan untuk mengukur kecepatan dari obyek yang bergerak. Range deteksi hingga 9 m (30 ft). Output berupa pulsa high dan low dengan nilai tegangan 3,9 V untuk level high dan 0 V untuk level low. Antarmuka dengan rangkaian eksternal melalui 4 pin SIP header dengan jarak antar pin 0,1". Tersedia pin untuk mengaktifkan modul dengan level TTL yang dilengkapi dengan internal pull-up resistor. Dilengkapi dengan resistor seri untuk antarmuka dengan Propeller chip. Tersedia VR untuk pengaturan sensitivitas pendeteksian gerakan. Catu daya 5 VDC. Tersedia contoh program menggunakan BASIC Stamp 2 dan Propeller chip. Dapat digunakan bersama sistem mikrokontroler/mikroprosesor yang lain. Perlengkapan X-Band Motion Detector: X-Band Motion Detector Module. Download Item: Manual X-Band Motion Detector.

This is the XBee XB24-Z7CIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU. This Xbee also has a chip antenna which is basically a small chip that acts as an antenna. Quick, easy, cheap, and not in the way. Digi Part #: XB24-Z7CIT-004 Warnings: Series 1 and Series 2 XBee modules have the same pin-out. However, Series 1 modules cannot communicate with Series 2 modules. Specification 3.3V @ 40mA 250kbps Max data rate 2mW output (+3dBm) 400ft (120m) range Built-in antenna Fully FCC certified 6 10-bit ADC input pins 8 digital IO pins 128-bit encryption Local or over-air configuration AT or API command set Shipping List XBee 2mW Chip Antenna - Series 2 ( Zigbee Mesh ) (1 unit) Documents Datasheet Dimensional Drawings Digi XBee Series 2 Page

Ini adalah modul XB24-Z7WIT-004 XBee dari Digi. Seri 2 meningkatkan pada output daya dan protokol data. Seri 2 modul memungkinkan Anda untuk membuat jaringan mesh kompleks berdasarkan firmware ZB XBee ZigBee mesh. Modul-modul ini memungkinkan komunikasi yang sangat handal dan sederhana antara mikrokontroler, komputer, sistem, benar-benar sesuatu dengan port serial! Titik ke titik dan multi-titik jaringan yang supported.These dasarnya perangkat keras yang sama seperti Seri 2,5 tua, tetapi memiliki update firmware. Mereka akan bekerja dengan Seri 2,5 modul jika Anda memperbarui firmware melalui X-CTU. spesifikasi 3.3V @ 40mA Max data rate 250kbps 2MW keluaran (+3 dBm) 400ft (120m) kisaran Built-in antena Sepenuhnya FCC disertifikasi 6 10-bit ADC masukan pin 8 digital IO pin 128-bit enkripsi Lokal atau melalui udara konfigurasi AT perintah atau set API dokumen Digi XBee Seri 2 Halaman datasheet dimensi Gambar SFE Elang Perpustakaan memiliki bagian ini! Tags: digi, 2MW, XBEE,

ntroduction This is the XBee XBP24-BZ7UIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU. u.FL Antenna – A tiny connector to connect your own antenna, this is great if your object is in a box and you want your antenna outside the box. Note: Series 1 and Series 2 XBee modules have the same pin-out. However, Series 1 modules cannot communicate with Series 2 modules. Note: If you are using these outside of the United States, please check with your local laws regarding radio communication. Specification 3.3V @ 295mA 250kbps Max data rate 50mW output (+17dBm) 1 mile (1600m) range Built-in antenna Fully FCC certified 6 10-bit ADC input pins 8 digital IO pins 128-bit encryption Local or over-air configuration AT or API command set Shipping List XBee Pro 50mW U.FL Connection - Series 2 (1 unit) Documents Digi XBee Series 2 Page Datasheet Dimensional Drawings SFE Eagle Library has this part!

This is the XBee XBP24-BZ7WI module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported. Series 2B modules use a different hardware configuration from the earlier models and while they will communicate with Series 2 XBee modules, they are not compatible with the outdated Series 2.5 Modules. Note: If you are looking for a simple point-to-point configuration, you might want to try the Series 1 instead. The Series 2 requires considerable setup and configuration. Note: Series 1 and Series 2B XBee modules have the same pin-out. However, Series 1 modules cannot communicate with Series 2B modules. Note: If you are using these outside of the United States, please check with your local laws regarding radio communication. Specification 3.3V @ 295mA 250kbps Max data rate 63mW output (+17dBm) 1 mile (1500m) range RPSMA connector Fully FCC certified 6 10-bit ADC input pins 8 digital IO pins 128-bit encryption Local or over-air configuration AT or API command set Shipping list XBee PRO 50mW Wire Antenna -Series 2 (ZB) (1 unit) Document Digi XBee Series 2.5 Page Datasheet

The XBee USB Adapter V2 is an update version from DFRobot. It features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Arduino Uno. The Atmega8U2 firmware uses the standard USB COM drivers, and no external driver is needed. However, on Windows, a .inf file is required. It's compatible with all the products using XBee socket. It provides a faster and stable wireless communication for your projects. The DFRobot Xbee USB adapter is used for the XBee module configuration parameters to facilitate wireless data transmission. It can be easily connected to a PC via mini USB cable. Further, it can be used with XBee-setting support software X-CTU. It can also be used as a USB-TTL adapter. It is compatible with: all XBee modules including the Series 1 and Series 2.5, standard and Pro version Bluetooth Bee DFRobot Wireless Programming Module Specification ZigBee X-CTU Compatible mini USB cable USB-TTL adapter function Voltage: +5V(USB Power) Shipping List XBee USB Adapter V2(1 unit) Documents Wiki Schematic X-CTU Software USB Drivers

Kondisi garansi adalah hanya untuk barang-barang yang ditawarkan oleh produsen. Anda mungkin bisa berkomunikasi dengan central electronics atau langsung dengan produsen. Central electronics adalah reseller dari banyak produk dan tidak bertanggung jawab dalam hal apapun atas kegagalan produk yang diproduksi oleh perusahaan lain.

At the beginning,the inertial measurement unit is an electronic device that measures and reports on a craft's velocity, orientation, and gravitational forces, using a combination of accelerometers,gyroscopes, and magnetometers. Now IMUs are commonly used in the Human-computer interaction(HCI), navigational purposes and balancing technology used in the Segway Personal Transporter as we all known. The 10 DOF(degrees of the freedom) sensor is a compact and low cost IMU from DFRobot. It integrates the ADXL345 accelerometer, the HMC5883L magnetometer,the ITG-3205 gyro and the BMP085 barometric pressure sensor. It's suitable for most of the controlling system because of the small dimension. The mounting holes make it possible to provide the highly accurate and stable sensor data.It embeds a low noise LDO regulator for supplying a wide range power input.Works with 3~8 volts power input.Certainly,the 10 DOF sensor is directly compatible with your Arduino boards. Applications Aircraft Balancing robots Indoor inertial navigation Altimeter Human–computer Interaction (HCI) Specification Wide power input range from 3 to 8 volts Low noise LDO regulator Low cost IMU Interface: I2C M3x2 holes for easily mounted on your mobile platforms,robots,HCI or UAVs LED power indication Integrate 10 dof sensors Adxl345 accelerometer ITG3200 gyro HMC5883L Compass BMP085 pressure sensor Compact size design and easy-to-use Compatible with Arduino controllers Electricity gold PCB Size: 26x18mm Shipping List 10 Dof Sensor 1unit 4P Pin Headers 1unit Documents Wiki Doc Arduino libraries and Sample codes Sensor datasheet package Schematic Sensor Layout Zip file with all of the above.

This is a Gear Motor w/Encoder, model No. GB37Y3530-12V-83R. It is a powerful 12V motor with a 131:1 metal gearbox and an integrated quadrature encoder that provides a resolution of 64 counts per revolution of the motor shaft, which corresponds to 8384 counts per revolution of the gearbox’s output shaft. These units have a 0.61" long, 6 mm-diameter D- shaped output shaft. This motor is intended for use at 12V, though the motor can begin rotating at voltages as low as 1V. The face plate has six mounting holes evenly spaced around the outer edge threaded for M3 screws. These mounting holes form a regular hexagon and the centers of neighboring holes are 15.5 mm apart. This motor is an ideal option for your mobile robot project. Warning: Do not screw too far into the mounting holes as the screws can hit the gears. Manufacturer recommends screwing no further than 3mm (1/8") into the screw hole. Specifications Gear ratio: 131:1 Free-run speed @ 12V: 83 rpm Free-run current @ 12V: 0.4A Rated torque @ 12V: 3 kg*cm Encoder Resolution: 64CPR(motor shaft)/8384CPR(gearbox shaft) Weight: 205g Shipping list GB37Y3530-12V-83R Gear Motor w/Encoder x1 Documents Dimensions Encoder instruction

DIODA 1N4002 10PCS

Diode 1n4007 dip, 10PCS

Doida 1Ampere 1000volt SMD di jual min 10pcs

DIODA SMD 1N 4148

1N5402 200V 3A General Purpose Diode

• Removable sliding cover • ON/OFF switch • 150mm leads (5mm tinned) • RoHS compliant

This is a very affordable 24Mhz 8 Channel USB Logic analyzer. This is a hobbyist level analyzer, ideal for testing your Arduino or other hobbyist microcontroller's communications. A logic analyzer is a must have tool for any serious electronics hobbyist. With a logic analyzer it is possible to see a visual representation of the zeros and ones that are flashing by between two components. A logic analyzer is different from an oscilloscope because the analyzer allows you to capture the data on a PC for a more detailed analysis of the data which is being transmitted and received. This logic analyzer supports 10 different communications standards (see Specifications below). with 8 channels it will allow you to monitor upto 8 differnet wires. So on an Arduino you could monitor the Serial port (tx/Rx pins), the I2C port (pins A4, A5), and the SPI port (pins 10, 11, 12, and 13) all at the same time. Specifications 8 Channels Supports triggering (rising, high, falling, low) Up to 24Mhz sampling Up to 10 Billion samples Max Voltage: 5.25Vdc supports: CAN DMX-512 I2C I2S/PCM Manchester 1-Wire Async Serial Simple Parallel SPI UNI/O Fully compatible with the Saleae Logic software Shipping List Logic Analyzer (1 unit) Mini USB Cable (1 unit) Jumper wire (10 units) Documents wiki Hack A Day- Saleae Logic Salae logic software

This is a4.8-46V, 2A Dual Motor Controller which is the revised version of the DF-MDV1.0. Its performance has been improved greatly. It can bear larger current due to the increased haetsink dissipation. It is easy to control, using LGS's outstanding high-power motor driver chip, the L298N. This chip allows for direct drive of two bi-directional DC motors, and incorporates high-speed short diodes for protection. Drive current up to 2A per motor output. The driver uses a broad-brush design to reduce wire resistance. Specification The logic part of the input voltage: 6 ~ 12V Driven part of the input voltage Vs: 4.8 ~ 46V The logical part of the work current Iss: 36mA Drive part of the operating current Io: 2A Maximum power dissipation: 25W (T = 75 degree Celsius) Control signal input level: High level: 2.3V = Vin = Vss Low:-0.3V = Vin = 1.5V Operating temperature: -25 degree Celsius ~ +130 degree Celsius Drive Type: Dual high-power H-bridge driver Module Size: 47 mm × 53mm Module Weight: About 29g Documents Wiki Doc Schematics

This Arduino Motor shield uses L298P chip which allow to drive two 7-12V DC motors with maximum 2A current. This shield can be directly mount onto standard Arduino Duemilanove and Arduino Mega. Specification 2 way 7-12V motor drive Up to 2A current each way Pin 5,6,7,8 are used to drive two DC motor Support PWM speed control Support PLL advance speed control Documents Manual