The ZM 0.3 Megapixel serial JPEG still camera module has a compact size, low power comsuption, and stable operation. 5.0V DC Supply. UART: Up to 115200bps for transferring JPEG images. The camera uses the advanced OmniVision OV7725 VGA color sensor JPEG CODEC for different resolutions. The camera also features down sampling, clamping and windowing circuits for VGA, QVGA, and no need for external DRAM. The use of the OmniVision CMOS VGA color sensor makes this a low powered comsuption unit. NOTE: The interface of this module is using RS232 protocol. Applications Embedded systems for imaging acquisition and control Security and Control systems, Remote or public monitoring. Retrieved/object detection and recognition. Robot/Industrial control, vehicle and medical systems. Specification 5V power supply Current consumption: 80-100mA Communication interface/protocol: RS232 VGA/QVGA/160x120 resolution Support capture JPEG from serial port Default baud rate of serial port is 115200 Size:1.51x1.51x1.26"(38.35x38.35x32mm) Wiring description (For included cable) Red wire +5v Black wire GND Green wire RS232 RX line Yellow wire RS232 TX line Documents 0.3M pixel datasheet test software pro test software lite software(pro) operation guide sample image Shipping List 0.3M pixel serial JPEG camera module(1 unit)

This Arduino Motor shield uses L298P chip which allow to drive two 7-12V DC motors with maximum 2A current. This shield can be directly mount onto standard Arduino Duemilanove and Arduino Mega. Specification 2 way 7-12V motor drive Up to 2A current each way Pin 5,6,7,8 are used to drive two DC motor Support PWM speed control Support PLL advance speed control Documents Manual

This is a4.8-46V, 2A Dual Motor Controller which is the revised version of the DF-MDV1.0. Its performance has been improved greatly. It can bear larger current due to the increased haetsink dissipation. It is easy to control, using LGS's outstanding high-power motor driver chip, the L298N. This chip allows for direct drive of two bi-directional DC motors, and incorporates high-speed short diodes for protection. Drive current up to 2A per motor output. The driver uses a broad-brush design to reduce wire resistance. Specification * The logic part of the input voltage: 6 ~ 12V * Driven part of the input voltage Vs: 4.8 ~ 46V * The logical part of the work current Iss: 36mA * Drive part of the operating current Io: 2A * Maximum power dissipation: 25W (T = 75 degree Celsius) * Control signal input level: * High level: 2.3V = Vin = Vss * Low:-0.3V = Vin = 1.5V * Operating temperature: -25 degree Celsius ~ +130 degree Celsius * Drive Type: Dual high-power H-bridge driver * Module Size: 47 mm × 53mm * Module Weight: About 29g

Product Description 1. 3.5" TFT, 320 x RGB x 240 dots 2. 24 bit RGB digital interface 3. 3.3v single power supply 4. Touch panel optional 5. Ideal choice for Display Systems on Industrial equipments, instrumentations, professional electronic control board and HMI. Diagonal Size Module Size mm A. A. mm Assem. Size 3.5“ 76.9 x 63.9 70.1 x 52.6 ---

TFT LCD 7.0" Touch Screen dapat digunakan untuk connek Mini2440 or Mini6410 development board.atau yg lain Spesifikasi Size: 7 inch Resolution: 800 x 480 Touch Screen Status . stock

Product Category: Encoders, Decoders, Multiplexers & Demultiplexers RoHS: No Product: Encoder Logic Family: 74C Number of Bits: 4 Number of Lines (Input / Output): 8.0 / 5.0 Propagation Delay Time: 150 ns at 5V, 80 ns at 10V, 60 ns at 15V Supply Voltage (Max): 15 V Supply Voltage (Min): 3 V Maximum Operating Temperature: + 85 C Package / Case: PDIP-18 Packaging: Tube Minimum Operating Temperature: - 40 C Mounting Style: Through Hole Number of Input Lines: 8.0 Number of Output Lines: 5.0 Power Dissipation: 700 mW

Razor IMU 9DOF menggabungkan empat sensor - sebuah (gyro tunggal-sumbu) LY530AL, LPR530AL (dual-axis gyro), ADXL345 (triple-sumbu accelerometer), dan HMC5843 (triple-sumbu magnetometer) - untuk memberikan sembilan derajat pengukuran inersia . Keluaran dari semua sensor diproses oleh on-board ATmega328 dan output melalui antarmuka serial. Dengan karya Jordi Munoz dan banyak lainnya, Razor 9DOF dapat menjadi Sikap dan Sistem Referensi Heading. Hal ini memungkinkan Razor 9DOF menjadi mekanisme kontrol yang sangat kuat untuk UAV, kendaraan otonom dan sistem stabilisasi gambar. Dewan datang diprogram dengan bootloader Arduino 8MHz dan firmware contoh bahwa tes output dari semua sensor. Cukup hubungkan ke pin TX dan RX serial dengan 3.3V FTDI Dasar Breakout, buka program terminal untuk 57600bps dan menu akan memandu Anda melalui pengujian sensor. Anda dapat menggunakan IDE Arduino untuk kode program Anda ke 9DOF, hanya pilih 'Arduino Pro atau Pro Mini (3.3V, 8MHz) w/ATmega328' sebagai forum Anda. 9DOF beroperasi pada 3.3VDC; setiap daya yang disediakan ke konektor JST putih akan diatur ke tegangan operasi ini. Header output dirancang untuk kawin dengan papan 3.3V kami Dasar FTDI Breakout, sehingga Anda dapat dengan mudah menghubungkan papan ke port USB komputer. Atau, solusi nirkabel, dapat dihubungkan ke Mate Bluetooth atau Explorer XBee.

This V2 Rotation Sensor is arduino compatible multi-ring rotation sensor. It is based on multi-turn precision potentiometer. It can rotate upto 10 laps. The voltage can be subdivided into 1024 copies. With the usage of special sensors expansion can be achieved accurately. It is easy to be connected to Arduino or DFRduino with our sensor expansion board. Specification Arduino compatible Interface type: Analog Pin Definition

Introduction The APC220 radio module provides a simple and economic solution to wireless data communications. The employment of an embedded high speed microprocessor and high performance IC creates a transparent UART/TTL interface, and elminates any need for packetizing and data encoding. Features Transmit distance up to 1000m (line of sight) @9600 bps 256 bytes data buffer High sensitivity (-112dbbm @9600 bps) GFSK modulation UART/TTL interface Embedded watch dog Size: 37x17x6.5 mm Shipping list APC220 module(2 units) Antenna for radio communication(2 units) USB to TTL Converter (CP210) (1 unit) Documents User guide Datasheet Wiki Doc RF-Magic Configure software

eatures: 4 degrees of freedom: ADXL335 - three axes of acceleration, ±3g range LISY300AL - one axis of angular velocity, ±300°/s range Compatible with ArduIMU 6DOF daughter boards to get up to 6 degrees of freedom Analog output of all 6 axes is sent to ArduIMU analog pins 0.1" pitch headers to connect to daughter boards and ArduIMU Dimensions: 0.9x0.6" Documents: Schematic LISY300AL datasheet ADXL335 datasheet ArduPilot Project Homepage Software and instructions: DIY Drones Community ArduPilot IMU Software Demo (YouTube)

The name says it all on this one. An ATmega328 in DIP package, pre-loaded with the Arduino UNO (16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded project without having to use an actual Arduino board. To get this chip working with Arduino IDE, you will need an external 16MHz crystal or resonator, a 5V supply, and a serial connection. If you are not comfortable doing this, we recommend purchasing the Arduino Duemilanove board that has all of these built into the board. Atmel's ATMega328 8-Bit Processor in 28 pin DIP package. It's like the ATmega168, with double the flash space. 32K of program space. 23 I/O lines, 6 of which are channels for the 10-bit ADC. Runs up to 20MHz with external crystal. Package can be programmed in circuit. 1.8V to 5V operating voltage! Documents Arduino Home Page Programming Reference Atmel Datasheets Tersedia juga Chip ATMEGA328 tanpa boothloader d

Manufacturer: Atmel Product Category: Microcontrollers (MCU) RoHS: RoHS Compliant Details Core: AVR8 Processor Series: ATMEGA32x Data Bus Width: 8 bit Maximum Clock Frequency: 16 MHz Program Memory Size: 32 KB Data RAM Size: 2.5 KB Data ROM Size: 1 KB On-Chip ADC: Yes Number of Programmable I/Os: 26 Number of Timers: 5 Package / Case: TQFP-44 Mounting Style: SMD/SMT A/D Bit Size: 10 bit A/D Channels Available: 12 Height: 1.05 mm Interface Type: SPI, TWI, USART Length: 10 mm Maximum Operating Temperature: + 85 C Minimum Operating Temperature: - 40 C Program Memory Type: Flash Standard Pack Qty: 800 Supply Voltage (Max): 5.5 V Supply Voltage (Min): 2.7 V Width: 10 mm

The 6DOF Atomic is a stripped-down IMU, designed to give good performance at a low price. The unit can run as a hard-wired UART interface (0-3.3V, 115200bps), or optionally with an XBee RF module, and is powered from a single LiPo (Lithium Polymer) battery. The processor is an Atmel ATMega328 running at 10MHz with 6 dedicated 10-bit ADC channels reading the sensors. Source code for the 6DOF Atomic is freely available and compiles with the free AVR GCC compiler. The 6-DOF Atomic uses these sensors: 1 x Freescale MMA7260Q TM triple-axis accelerometer, settable to 1.5g, 2g, 4g or 6g sensitivity 3 x ST Microelectronics LISY300AL TM single-axis, 300°/s gyros All sensor readings are available through any terminal program in either ASCII or binary format, or with the 6DOF Atomic IMU Mixer demo application (source code also available). Having a hard time picking an IMU? Our Accelerometer, Gyro, and IMU Buying Guide might help! Specifications Input voltage: 3.4V to 10V DC Current consumption: 24mA (75mA with X-bee) Sensor bandwidth and resolution: LISY300AL Gyros: 88Hz, 0.977°/s/tick (ADC count) MMA7260Q Accelerometer: 350Hz, X and Y axes 150Hz, Z axis 0.00403g/tick @ 1.5g 0.00537g/tick @ 2g 0.0107g/tick @ 4g 0.0161g/tick @ 6g Dimensions: 1.85 x 1.45 x 0.975 inches (47 x 37 x 25 mm) Documents Datasheet Schematic Source Code Atomic Mixer

Manufacturer: Atmel Product Category: Microcontrollers (MCU) RoHS: RoHS Compliant Details Core: AVR8 Processor Series: ATXMEGA128x Data Bus Width: 8 bit, 16 bit Maximum Clock Frequency: 32 MHz Program Memory Size: 128 KB Data RAM Size: 8 KB Data ROM Size: 2 KB On-Chip ADC: Yes Number of Programmable I/Os: 78 Number of Timers: 8 Operating Supply Voltage: 1.6 V to 3.6 V Package / Case: TQFP-100 Mounting Style: SMD/SMT A/D Bit Size: 12 bit A/D Channels Available: 8 Height: 1 mm Interface Type: SPI, USART, TWI Length: 14 mm Maximum Operating Temperature: + 85 C Minimum Operating Temperature: - 40 C Packaging: Tray Program Memory Type: Flash Standard Pack Qty: 90 Supply Voltage (Max): 3.6 V Supply Voltage (Min): 1.6 V Width: 14 mm

CAM130 CMOS-Camera Module Pixel: 1.3 megapixel Resolution: 640 x 480 / 1280 x 1024 Color: 24 bit Transmission rate: 30/15 fps Chip: OV9650

Pixel: 1.3 megapixel Resolution: 640 x 480 / 1280 x 1024 Color: 24 bit Transmission rate: 30/15 fps Chip: OV9650

Sekarang, saatnya untuk menambahkan cara interaktif yang lebih mewah untuk proyek Anda. Kit ini dilengkapi dengan sentuhan DFRobot tiga jenis sensor sentuh. Sebuah roda ipod touch styple, sentuhan tombol backlit yang mendukung dan touch pad grid yang dapat recoginze sesuatu yang unik. Kit ini memanfaatkan teknologi sentuh tidak terlalu "terbaru" capactive yang membuat penginderaan sangat sensitif. Kit ini dirancang agar kompatibel dengan Arduino. Specfication Operasi Voltage: 5V Sensor Type: Capacitive Sentuh Chip: MPR121 dokumen wiki Doc schematics Arduino Perpustakaan MPR121 Datasheet Daftar pengiriman Control Unit (1 Unit) Pad roda (1 unit) Keypad (1 unit) Grid Pad (1 unit) Kabel (1 unit) Tags: Sentuh Capacitive Kit,

DF-BluetoothV3 Bluetooth module uses a unique double-board design, it is beautiful and aim to prevent electrostatic damage to the module. It is designed to have 2 DC power input, wide voltage supply (3.5V ~ 8V) and 3.3V power supply, suitable for various applications. STATE LINK is indicated by a clear and bright LED which is used to display module status and connection status (STATE state: Search state (high 104ms 342ms 2.9Hz cycle flicker) connection status (high 104ms period 2s 0.5Hz flashing), LINK state: paired ). It has build-in on-board antenna which provides high quality signals. DIP switch is designed to set the module status, LED Off to turn off the LINK light to enter power saving mode, AT Mode allows the module to enter AT command mode, AT commands can modify the baud rate and the master and slave mode. This module can also be used as a pair which provides a transparent serial data communication. This module has been tested and compatible with most Bluetooth adapter in the market (Bluetooth dongle, including laptops and mobile phones). Specifications * The Bluetooth chip: CSR BC417143 * Bluetooth protocol: Bluetooth Specification v2.0 + EDR * USB Protocol: USB v1.1/2.0 * Operating frequency: 2.4 ~ 2.48GHz unlicensed ISM band * Modulation: GFSK (Gaussian Frequency Shift Keying) * Transmit Power: ≤ 4dBm, Class 2 * Transmission distance: 20 ~ 30m in free space * Sensitivity: ≤-84dBm at 0.1% BER * Transfer rate: Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps/1Mbps * Safety features: Authentication and encryption * Support profiles: Bluetooth serial port * Serial port baud rate: 4800 ~ 1382400 / N / 8 / 1 default: 9600 * LED indicator: STATE state: Search state (high 104ms 342ms 2.9Hz cycle flicker) connection status (high 104ms cycle 2s 0.5Hz flashing), LINK Status: Always after match * Input Voltage: +3.5 V ~ +8 V DC and 3.3V DC/50mA * Working temperature: -20 ℃ ~ +55 ℃ * Module Size: 40 × 20 × 13mm Documents * Wiki Doc * Datasheet

The LEA-5H is a high performance stand-alone GPS and GALILEO receiver module designed to allow easy, straightforward migration from its LEA-4 predecessors. It features u-blox' KickStart weak signal acquisition technology, as well as flexible connectivity options. The LEA-5H comes with built-in Flash memory that enables firmware updates and the storage of specific configuration settings in a non-volatile RAM. The built-in antenna supervisor supports external and active antennas, such as u-blox' ANN high performance GPS antenna. u-blox KickStart provides accelerated startup at weak signals, and our featured SuperSense® Indoor GPS is capable of tracking and acquiring even extremely weak signals. This makes the LEA-5H suitable for solutions using small or covert antennas. Specification Easy migration from LEA-4H and LEA-4P modules Accelerated startup at weak signals thanks to KickStart Technology Operating voltage: 2.7 - 3.6 V LEA-5H Reference design documentation available with ceramic or GeoHelix antenna, UART and USB 2 Hz position update rate Built-In Flash memory for fimware upgrades and storage of specific configuration settings Antenna supervisor and supply Antenna short and open circuit detection and protection for external antennas 1 UART, 1 USB and 1 DDC (I2C compliant) interface GALILEO-ready 50-channel u-blox 5 engine with over 1 million effective correlators Under 1 second Time-To-First-Fix for Hot and Aided Starts SuperSense® Indoor GPS: -160 dBm tracking sensitivity Supports AssistNow Online and AssistNow Offline A-GPS services; OMA SUPL compliant Supports SBAS (WAAS, EGNOS, MSAS, GAGAN) Operating temperature range: -40 to 85°C RoHS compliant (lead-free) Documents Ublox LEA-5h Webpage Ublox Resource Schematics GPS Data Sheet Drivers&Software Wiki Doc (Sample code is in wiki page) Shipping List GPS Shield (1 unit) Passive Attena (1 unit)

DHT11 Temperature and Humidity Sensor

Spesifikasi: Menggunakan sensor suhu dan kelembapan terkalibrasi produk sensirion, SHT11, sebagai komponen utama. Spesifikasi sensor SHT11: Terkalibrasi: Celcius dan Fahrenheit. Daerah pengukuran: [(-40) – 123.8]ºC. Akurasi: ±0.4ºC. Terkalibrasi: %RH. Daerah pengukuran: [0 – 100]%. Akurasi: ±3.0% Tegangan sumber: 2.4VDC – 5.5VDC. Output: serial dua lajur (two-wires serial). Tersambung dengan kabel serat yang terbungkus GND sepanjang 500mm dengan female-connector pada ujung kabel. Suhu: Kelembapan: Deskripsi Perangkat Modul: Dimensi: Jumlah lajur: 4 + 1 (selubung = GND) Panjang: 500mm PCB: 12.2mm(X) x 28.8mm(Y) x 1.9mm(Z) Kabel: Tabel 1. Fungsi tiap lajur kabel Kabel Fungsi 1 Hitam GND Sumber (-) 2 Merah VCC Sumber (+) 3 Kuning Data Output Sensor 4 Putih Clk Serial Clock Aplikasi: Sensor / pengukur: temperatur / suhu humidity / kelembapan

This green LED light module has a shiny white color. It is ideal for Arduino starter. This module can be easy to be plugged on IO/Sensor expansion shield. Specification Type:Digital LED light module pin definition : (1) control terminal (2) power supply (3) ground Documents Shipping List Sensor (1 unit) Digital Sensor Cable (1 unit) (SKU:FIT0011)

This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector. The pins labeled BLK and GRN correspond to the colored wires on the FTDI cable. The black wire on the FTDI cable is GND, green is DTR. Use these BLK and GRN pins to align the FTDI basic board with your Arduino target. There are pros and cons to the FTDI Cable vs the FTDI Basic. This board has TX and RX LEDs that allow you to actually see serial traffic on the LEDs to verify if the board is working, but this board requires a miniB cable. The FTDI Cable is well protected against the elements, but is large and cannot be embedded into a project as easily. The FTDI Basic uses DTR to cause a hardware reset where the FTDI cable uses the RTS signal. This board was designed to decrease the cost of Arduino development and increase ease of use (the auto-reset feature rocks!). Our Arduino Pro and LilyPad boards use this type of connector. Specification 3.3/5V output(switchable via Jumpers) Documents Schematics Compatiblity DFRduino Funnel I/O (Fio) 9 DOF IMU unit

The GPRS (General Packet Radio Service) Shield is a new nonvoice value added service that delivers GSM/GPRS 850/900/1800/1900MHz performance for voice, SMS, Data, and Fax in a small form factor and with low power consumption. It is controlled via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands), and fully compatible with Seeeduino/Arduino and Mega. The GPRS Shield has 12 GPIOs 2 PWMs and 1 ADC(They are all 2V8 logic). Features Quad-Band 850/ 900/ 1800/ 1900 MHz GPRS multi-slot class 10/8 GPRS mobile station class B Compliant to GSM phase 2/2+ Class 4 (2 W @850/ 900 MHz) Class 1 (1 W @ 1800/1900MHz) Control via AT commands (GSM 07.07 ,07.05 and SIMCOM enhanced AT Commands) Low power consumption: 1.5mA(sleep mode) Operation temperature: -40°C to +85 °C Documents Please visit our wiki page for more info about this product. It will be appreciated if you can help us improve the documents, add more demo code or tutorials. For technical support, please post your questions to our forum.

Tampilan ini LCD4884 menyediakan layar 48x48. Jika proyek Anda membutuhkan informasi lebih untuk menampilkan, tampilan LCD tampaknya dapat memenuhi kebutuhan Anda. Hal ini dapat menampilkan bahasa Inggris, Chines, bahkan gambar. Hal ini juga mengintegrasikan sebuah joystick DOF 5. Perisai memiliki 6 Digital IO dan IO Analog 5. Catatan: Arduino dalam gambar TIDAK termasuk. spesifikasi Power Supply: 5V SPI Interface (menggunakan Arduino Digital Pin 2,3,4,5,6) Satu Tombol Reset Satu 5 derajat joystick (menggunakan Arduino Analog Pin 0) Backlit kontrol (Arduino DIO Pin 7) dokumen silahkan klik http://www.dfrobot.com/wiki/index.php?title=LCD4884_Shield_Fro_Arduino_%28SKU:DFR0092%29 juga tersedia Arduino Library

Introduction The Joystick / Input Shield for Arduino include a two axis mini joystick (with moment switch) as well as two colored push buttons. The shield easily connects to your Arduino using male to male pin headers. Features Dual axis mini joystick Connects to your Arduino using male to male pin headers Comes with 2 colored push buttons The use of imported high-quality potentiometers and the PS button rocker. The rocker output an analog signal is to achieve vertical and horizontal control, which is attached to four keys at the same time. It also has two great circle button caps (cap color random round keys), a rocker button and a reset button. The use of stack design is so that the plug can easily on Arduino Duemilanove or DFRduino Romeo. The reserved APC220/Bluetooth module interface is to facilitate the realization of wireless rocker button controller. The remaining unused ports are extended out of standby. Shipping list Input Shield For Arduino (1 unit) Documents Product Wiki Page Schematic